| 17 Jun 2024 |
 Jan-Peter | How to sink in the out most screws? | 18:40:21 |
| Jan-Peter | Also, its my first time using freecad.
very addictive. But you need some time to get used to it. | 18:40:57 |
| Jan-Peter | Download 3U_FrameA.FCStd | 18:43:10 |
 Artur Scholz | Use hole with iso metric threaded profile | 19:47:40 |
| Jan-Peter | i did | 19:53:29 |
| 18 Jun 2024 |
|  Rajath-Pai changed their display name from phantom-observer to Rajath-Pai. | 06:08:44 |
| Rajath-Pai set a profile picture. | 06:09:09 |
| Jan-Peter | 
Download image.png | 06:27:47 |
| Jan-Peter | Ok
I got it.
I was on the wrong plane | 06:27:54 |
| Jan-Peter | But something is wrong with my measurements ...
The top whole at the bottom unit and the bottom whole at the next unit are 28mm apart, as in the 2U example, but within their units, their still not correct .. | 06:29:55 |
| Artur Scholz | Compare the 1u with 2u. I remember there was same issue. | 06:40:27 |
| Artur Scholz | Jan-Peter: Problem solved? Maybe Babalola Emmanuel can give support? | 20:10:09 |
| Artur Scholz | And do you have a 3D printer large enough to print it? | 20:10:28 |
 Babalola Emmanuel | In reply to @jan-peter:matrix.org
Ok
I got it.
I was on the wrong plane I hope you've been able to find solution to that? | 20:27:02 |
| 19 Jun 2024 |
| Jan-Peter | In reply to @artur.librecube:matrix.org
And do you have a 3D printer large enough to print it? I have a meeting with the right institute later (regarding something else) - I will ask them. | 06:33:22 |
| Jan-Peter | Otherwise I will have to print it in copper 🤪 | 06:33:49 |
| Jan-Peter | In reply to @babalola_emmanuel:matrix.org
I hope you've been able to find solution to that? the plane yes.
The postioning, not yet | 06:34:16 |
| 20 Jun 2024 |
| Jan-Peter | 
Download image.png | 06:23:49 |
| Jan-Peter | 3U CubeSat FrameB is done 🥳 | 06:24:05 |
| Jan-Peter | Although I i have small issue with one of the holes.
Maybe you can spot it here 😄 | 06:24:35 |
| Jan-Peter | Artur Scholz: maybe you could set up a repo in gitlab or whatever you think works best. | 06:25:04 |
| Jan-Peter | Just in Case I upload the file here: | 06:25:14 |
| Jan-Peter | Download 3U_FrameB.FCStd | 06:25:35 |
| Jan-Peter | I couldn't find a printer large enough to print it yet, so I will slice it in 2 parts and glue it together | 06:26:09 |
| Artur Scholz | In reply to @jan-peter:matrix.org
Artur Scholz: maybe you could set up a repo in gitlab or whatever you think works best. https://gitlab.com/librecube/prototypes/platform-3u-structure | 11:42:39 |
| 21 Jun 2024 |
|  bopnic joined the room. | 06:37:56 |
| Jan-Peter | next step in my journey to 3U Mockups: eps | 07:20:31 |
| Jan-Peter | I found the kicad model and it should be possible to export that 3D model to STEP, but i get an error and it says I should run the DRC. So, I do: | 07:21:30 |
| Jan-Peter | 
Download image.png | 07:21:34 |
| Jan-Peter | * I found the kicad model (which can dispaly a 3D view internally with warnring) and it should be possible to export that 3D model to STEP, but i get an error and it says I should run the DRC. So, I do: | 07:22:01 |
