19 Nov 2023 |
@1dre:matrix.org | They did but have been oos for a while | 13:53:44 |
chickenquat | ok thanks. The Redman barrel 1-16 twist is oos but the 1-20 twist is available. Will that cause any issues / has anyone tested it? | 13:55:12 |
chickenquat | * ok thanks. The Redman barrel 1-16 twist is oos on brownells but the 1-20 twist is available. Will that cause any issues / has anyone tested it? | 14:01:25 |
chickenquat | https://www.dixiegunworks.com/index/page/product/product_id/1186/category_id/383/product_name/BR1217+.22+Caliber+Rimfire+Barrel+Liner+-+18%22+Length | 15:03:43 |
chickenquat | This should work. Doesn't say what the outer diameter is but hopefully it is workable. | 15:04:31 |
zer0fux | In reply to @chickenquat:matrix.org https://www.dixiegunworks.com/index/page/product/product_id/1186/category_id/383/product_name/BR1217+.22+Caliber+Rimfire+Barrel+Liner+-+18%22+Length worst case scenario, you chuck it in a drill and spin it in sandpaper this is how we turned down the first ones | 15:06:09 |
chickenquat | Thanks that is the plan! and 18" is adequate length correct? I was reading through this chat and seeing people arriving at around 17 1/2 etc length. | 15:07:25 |
zer0fux | i think mine was 19.5 | 15:20:52 |
zer0fux | but you can go smaller | 15:21:00 |
Jak || Gats and geckos | Mine was 16.1" | 15:21:34 |
chickenquat | Awesome thanks!! | 15:23:55 |
| zer0fux changed their display name from zer0fux | Randy Marsh of GunCAD to zer0fux. | 18:33:20 |
imrcly | Mine I did 17 cause lazy and sandpaper with the shaft in a drill held in a vice I started with 60 grit and ended with 600 | 21:40:14 |
zer0fux | Redacted or Malformed Event | 23:22:22 |
22 Nov 2023 |
| poolboy changed their profile picture. | 02:08:07 |
23 Nov 2023 |
chickenquat | What infill are you guys using for the stock? | 00:29:34 |
zer0fux | what platform are you using to host the gatlatl? (just so I know what stock you are using)... | 00:36:04 |
zer0fux | chickenquat: | 00:36:23 |
imrcly | I need to look at the safety I am annoyed that went out not working | 00:58:30 |
imrcly | But also have a short memory | 00:58:43 |
zer0fux | In reply to @imrcly:matrix.org I need to look at the safety I am annoyed that went out not working you must be using coops g22-v4 | 00:59:30 |
chickenquat | In reply to @fleece_johnson:matrix.org what platform are you using to host the gatlatl? (just so I know what stock you are using)... Grizzly g22 v3. Mk4 2 piece stock. | 01:33:21 |
chickenquat | I’m doing the a2 grip part at 100 since it attaches to the frame but didn’t figure the stock and buttpad needed to be near 100 infill. | 01:37:06 |
zer0fux | 6-8 walls and 35 or so infill | 01:46:55 |
zer0fux | chickenquat: | 01:47:05 |
zer0fux | its my default to always have 6-8 walls. | 01:47:26 |
imrcly | Yeah, very unhappy about that release, lots of cool stuff but it wasn't completed | 01:48:31 |
zer0fux | you are the only one I know that has had and issue with the safety... I never finished the build myself. | 01:49:10 |
zer0fux | too many irons in the fire. | 01:49:29 |
zer0fux | whats preventing the safety from working? | 01:49:37 |